Zhejiang Delong Teflon And Plastic Technology Co.,Ltd
+86-572-8837389
Products
[[TD-Hot Products]]
Knowledge
Home > Knowledge > Content

5mm PTFE Sheet/ Rod / Tube

Basic Info


PTFE gasket sheet/rod

Specifications:
1. Heat resistance property---It is able to wok stably between -180° C to +260° C.
2. Excellent non-sticky property---It easier to remove those resin, dopes, oil and other sticky things.
3. Good mechanical property with no distortion and low friction coefficient.
4. Excellent insulation property.
5. Materials like carbon, graphite and glass fiber can be filled.
6. Virgin and recycled materials are available.

Size:
(1) Min. Thickness=0.1mm, Max. Thickness=0.5mm, Max. Width= 1.2m
(2) Min. Thickness=0.5mm, Max. Thickness=6mm, Max. Width= 2.5m

Application:
1. Besing stuck to the heating up flat to reduce the friction.
2. Used in wrapping the cables under high voltage and high temperature.
3. Being used in sealing the electronic parts.

PTFE die-pressed sheet, PTFE Molded Sheet

Specifications:
PTFE molded sheet is manufactured by molding method with PTFE granular resin.
PTFE possesses the best chemical resistance of all known plastics. It does not age. It has the lowest coefficient of friction of all known solid materials and a wide range of practicable temperature from -180 to 260.

1. Stretch strength: >15Mpa
2. Break elongation rate: 200%
3. Virgin and recycled materials available
4. Size can be made based on customers' requirement.
5. Carbon, graphite can be filled

Size:
1. Length× Width: 150× 150mm--2000× 2000mm or as your requirements
2. Thickness: 3-100mm

Application:
1. Anti-corrosion lined materials
2. Sealing lined materials
3. Lining bearing pads
4. Slide block slippers
5. Dielectric parts, etc.

100% Virgin PTFE Teflon Moulded Tube

Specifications:
1. Melting point: 327° C
2. Yield strength: 23MPa
3. Density: 2200 kg/m3
4. Coefficient of friction<0.10
5. Strong chemical-resistant
6. Flat and tidy surface, no defects, crevices and separations
7.100% virgin PTFE resin and recycled materials available
8. Carbon, graphite can be filled

Size:
1. O. D. 25mm-1200mm and wall thickness 5mm-500mm die-pressed / moulded. Min Length: 100mm, Max. Length: 300mm
2. Wall thickness: 5mm-500mm

Application:
Insulating jacket of lead, pipeline of corrosive liquid medium, insulating parts under kinds of high frequencies.

Teflon PTFE rod

Specifications:
PTFE Rod is manufactured in two distinct ways, extruded PTFE Rod is the most popular and is relevant to smaller sizes, Molded PTFE Rod is relevant to the diameters over 100mm in size, smaller sizes are also available in extruded form. Molded Teflon rod has a wide range of practicable temperature from -180&#176; C - +260&#176; C and a wax-like surface to which anything hardly rods. Molded PTFE rod has the lowest coefficient of friction of all known solid materials.
1. It has the best electrical properties of all plastics.
2. Carbon, graphite can be filled

Sizes:
1. Extruded Rod Min. Diameter= 5mm, Max. Diameter= 150mm, Length= normal 1 m, or according to customer's request
2. Moulded Rod Min. Diameter= 5mm, Max. Diameter=300mm, Length: Max. 300mm

Application:
PTFE molded rod is use of the products the electrical insulation used under various kinds of frequency, the sesal liner of various kinds of corrosively medium, antis ticking materials, lubrication material.

  • Company Profile
    DELONG is one of the top level China ptfe tube manufacturers and suppliers, as a professional exporter with productive factory, we are able to provide virgin and white insolution and lubricate ptfe tube, hdpe sheet, ptfe filled, ptfe film, ptfe hose, ptfe membrane, teflon board, teflon pipe, teflon sheet products with low price and good quality. Welcome to buy cheap products from us....
  • Product Category
  • Contact Us
    Address:No.269 Zishan Road, Wukang Economic Development Zone,Deqing County, Huzhou City, Zhejiang Province, China
    Tel: +86-572-8837389
    Fax: 86-572-8837089